Known Issues

Known defects and limitations in AMD EDF v26.11, with workarounds where one exists.

Open Issues

Linux/Bare-Metal

Components

Platform/SoC Supported

Description

Work-Around

To be fixed version

Linux

BSP, image-mgmt

Kria SoM

Image management does not yet handle the Kria-specific QSPI flash layout.

None. Answer record 000041139

2027.1

Linux

BSP, image-recovery-linux

ZynqMP (ZCU104)

image-recovery-cli --version does not retrieve and display the version information correctly.

None. Answer record 000041035

2027.1

Linux

PLM

Versal

The UART can stop working during boot, because the AMBA driver releases the device.

Delete the power-domains property so that power management does not run during boot:

&serial1 { /delete-property/ power-domains; };

2027.1

Linux

BSP

VHK158

The PS cannot reach HBM during the initial boot when the path is configured with initial_boot=false, so accessing that memory from U-Boot can hang. Xen boot hangs with the prebuilt artifacts for the same reason.

For HBM access, set the PS/APU path to initial_boot=true in the board design, regenerate the hardware description, and rebuild the boot firmware. For Xen, exclude the HBM node from the device tree and rebuild the boot firmware. Answer record 000040935

2027.1

Linux

VCU2, multimedia

VEK385 revB

With HEVC constant bit rate encoding (omxh265enc) the start code or header of filler-data network abstraction layer (NAL) units is sometimes corrupted in the output stream. Slice data is unaffected.

Set filler-data=false on omxh265enc.

2027.1

Linux

VCU2, multimedia

VEK385 revB

Stopping an MJPEG decode (omxjpegdec) before the end of the stream leaves the decoder firmware unresponsive, and the pipeline aborts on teardown.

Let the stream reach end of stream. If the decoder stops responding, reload the VCU2 kernel modules.

2027.1

Linux

VCU2, multimedia

VEK385 revB

The ctrlsw_decoder test application (HEVC) can hang instead of exiting when it is given non-video or corrupted input.

Pass only valid video input to ctrlsw_decoder, or stop the process manually.

2027.1

Linux

VCU, multimedia

ZynqMP (ZCU106)

File-based decode to the PS DisplayPort output shows green frames at 4Kp30, and at 2Kp60 with XV20, when the VCU decoder uses PL DDR. The extra memory latency causes it; the decoded output itself is correct.

Use 1080p60 output, or write the decoded output to a file.

2026.2.1

Linux

VCU, multimedia

ZynqMP (ZCU106)

In the LLP1 and LLP2 low-latency GStreamer use cases on the PL DDR HDMI and SDI designs, the decoder hangs and reports Timeout - resetting the decoder.

None at this time; under investigation.

2027.1

Linux

MMI DC, DP TX

VEK385 revB, VMK365

Four-stream Multi-Stream Transport (MST) does not work.

None.

2027.1

Linux

MMI DC

VEK385 revB, VMK365

Non-live audio does not work at 44.1 kHz, 88.2 kHz, or 176.4 kHz.

None.

2027.1

Linux

MMI DC

VEK385 revB

DisplayPort does not work when USB and DP TX are used at the same time.

None.

2027.1

Bare metal

MMI DC, DP TX

VEK385 revB

Some resolutions do not appear on the monitor.

None.

2027.1

Linux

MMI DP TX

VEK385 revB, VMK365

The monitor works only after the cable is reversed.

None. Answer record 000039239

2027.1

Bare metal

Power management

VEK385

After an in-place PLM firmware update, the firmware can lose the record that a PL hardware self-test completed, so a later operation may run that self-test again.

None.

2027.1

Linux

GPU, Lima

ZynqMP

Some conformance test suite (CTS) tests fail because of known limitations in the Lima driver.

None.

Not yet assigned

Linux

NoC performance demo

VPK180

DDR memory controller (DDRMC) performance events are unavailable in the VPK180 NoC performance demo. perf list lists NoC master unit (NMU) events, but does not list DDRMC events (ddrmc_*_nsu*).

None.

2027.1