Connecting to device com0. Use Ctrl-\ to escape. Zynq MP First Stage Boot Loader Release 2025.2 Oct 24 2025 - 13:29:14 PMU Firmware 2025.2 Oct 24 2025 13:29:14 PMU_ROM Version: xpbr-v8.1.0-0 NOTICE: BL31: Non secure code at 0x8000000 NOTICE: BL31: v2.12.0(release):xlnx_rebase_v2.12_2025.1-165-g894ecd073-dirty NOTICE: BL31: Built : 08:14:53, Oct 16 2025 U-Boot 2025.01-g91d06b67db04 (Oct 17 2025 - 09:09:58 +0000) CPU: ZynqMP Silicon: v3 Chip: zu9eg Model: ZynqMP ZCU102 Rev1.0 Board: Xilinx ZynqMP DRAM: 2 GiB (effective 4 GiB) gpio_hog_of_to_plat: wrong gpios property, 2 values needed -22 gpio_hog_of_to_plat: wrong gpios property, 2 values needed -22 EL Level: EL2 Secure Boot: not authenticated, not encrypted Core: 79 devices, 30 uclasses, devicetree: board NAND: 0 MiB MMC: mmc@ff170000: 0 Loading Environment from FAT... Unable to use mmc 0:2... In: serial Out: serial,vidconsole Err: serial,vidconsole Bootmode: LVL_SHFT_SD_MODE1 Reset reason: DEBUG Net: ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id Warning: ethernet@ff0e0000 (eth0) using random MAC address - 4e:4a:f9:80:71:e4 eth0: ethernet@ff0e0000 scanning bus for devices... SATA link 0 timeout. Target spinup took 0 ms. AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Device 0: (1:0) Vendor: ATA Prod.: ST3160215SCE Rev: 3.AC Type: Hard Disk Capacity: 152627.8 MB = 149.0 GB (312581809 x 512) starting USB... Bus usb@fe200000: Register 2000440 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus usb@fe200000 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:2... Found U-Boot script /boot.scr 977 bytes read in 9 ms (105.5 KiB/s) ## Executing script at 20000000 Checking for kernel:Image Loading Image at 0x200000 32780800 bytes read in 2126 ms (14.7 MiB/s) Working FDT set to 7bcd52c0 Cannot persist EFI variables without system partition Missing TPMv2 device for EFI_TCG_PROTOCOL Missing RNG device for EFI_RNG_PROTOCOL No RNG device Booting /Image EFI stub: Booting Linux Kernel... EFI stub: EFI_RNG_PROTOCOL unavailable EFI stub: Using DTB from configuration table EFI stub: Exiting boot services... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.40-xilinx-g3f587f532ea7 (oe-user@oe-host) (aarch64-amd-linux-gcc (GCC) 13.4.0, GNU ld (GNU Binutils) 2.42.0.20240723) #1 SMP Thu Oct 23 09:14:44 UTC 2025 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: ZynqMP ZCU102 Rev1.0 [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [cdns0] enabled [ 0.000000] efi: EFI v2.10 by Das U-Boot [ 0.000000] efi: ESRT=0x87ffc2040 RTPROP=0x87ffc4040 SMBIOS 3.0=0x7bd08000 MEMRESERVE=0x87ffa0040 [ 0.000000] esrt: Reserving ESRT space from 0x000000087ffc2040 to 0x000000087ffc20a0. [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000087fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007bd07fff] [ 0.000000] node 0: [mem 0x000000007bd08000-0x000000007bd08fff] [ 0.000000] node 0: [mem 0x000000007bd09000-0x000000007fd5ffff] [ 0.000000] node 0: [mem 0x000000007fd60000-0x000000007fd6ffff] [ 0.000000] node 0: [mem 0x000000007fd70000-0x000000007fefffff] [ 0.000000] node 0: [mem 0x0000000800000000-0x000000087ffc3fff] [ 0.000000] node 0: [mem 0x000000087ffc4000-0x000000087ffc4fff] [ 0.000000] node 0: [mem 0x000000087ffc5000-0x000000087ffc7fff] [ 0.000000] node 0: [mem 0x000000087ffc8000-0x000000087ffe8fff] [ 0.000000] node 0: [mem 0x000000087ffe9000-0x000000087ffeafff] [ 0.000000] node 0: [mem 0x000000087ffeb000-0x000000087ffebfff] [ 0.000000] node 0: [mem 0x000000087ffec000-0x000000087fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000087fffffff] [ 0.000000] On node 0, zone Normal: 256 pages in unavailable ranges [ 0.000000] cma: Reserved 256 MiB at 0x000000006bc00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.5 [ 0.000000] percpu: Embedded 31 pages/cpu s90072 r8192 d28712 u126976 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 root=/dev/ram0 rw init_fatal_sh=1 root=/dev/mmcblk0p3 ro rootwait uio_pdrv_genirq.of_id=generic-uio [ 0.000000] Unknown kernel command line parameters "init_fatal_sh=1", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1048320 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x000000007bd60000-0x000000007fd60000] (64MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0x1ffffffffffffff max_cycles: 0x170f8de2d3, max_idle_ns: 440795206112 ns [ 0.000001] sched_clock: 57 bits at 100MHz, resolution 10ns, wraps every 4398046511101ns [ 0.008452] Console: colour dummy device 80x25 [ 0.012561] Calibrating delay loop (skipped), value calculated using timer frequency.. 199.98 BogoMIPS (lpj=399960) [ 0.022974] pid_max: default: 32768 minimum: 301 [ 0.027719] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.034991] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.044569] rcu: Hierarchical SRCU implementation. [ 0.047603] rcu: Max phase no-delay instances is 1000. [ 0.053002] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.061248] Remapping and enabling EFI services. [ 0.065732] smp: Bringing up secondary CPUs ... [ 0.262081] Detected VIPT I-cache on CPU1 [ 0.262151] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.558059] Detected VIPT I-cache on CPU2 [ 0.558109] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.871215] Detected VIPT I-cache on CPU3 [ 0.871265] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.871332] smp: Brought up 1 node, 4 CPUs [ 0.901369] SMP: Total of 4 processors activated. [ 0.906067] CPU: All CPU(s) started at EL2 [ 0.910159] CPU features: detected: 32-bit EL0 Support [ 0.915292] CPU features: detected: CRC32 instructions [ 0.920471] alternatives: applying system-wide alternatives [ 0.926991] Memory: 3746772K/4193280K available (18944K kernel code, 2380K rwdata, 5848K rodata, 4736K init, 505K bss, 180052K reserved, 262144K cma-reserved) [ 0.940935] devtmpfs: initialized [ 0.953058] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.957196] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.969016] 24624 pages in range for non-PLT usage [ 0.969032] 516144 pages in range for PLT usage [ 0.969226] pinctrl core: initialized pinctrl subsystem [ 0.979081] SMBIOS 3.7.0 present. [ 0.981899] DMI: xlnx ZynqMP ZCU102 Rev1.0/ZynqMP ZCU102 Rev1.0, BIOS 2025.01-g91d06b67db04 01/01/2025 [ 0.991215] DMI: Memory slots populated: 0/0 [ 0.997426] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 1.002134] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 1.008521] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 1.016322] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 1.024118] audit: initializing netlink subsys (disabled) [ 1.029629] audit: type=2000 audit(0.944:1): state=initialized audit_enabled=0 res=1 [ 1.029943] thermal_sys: Registered thermal governor 'step_wise' [ 1.037433] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 1.050087] ASID allocator initialised with 65536 entries [ 1.055560] Serial: AMBA PL011 UART driver [ 1.070014] /axi/pcie@fd0e0000: Fixed dependency cycle(s) with /axi/pcie@fd0e0000 [ 1.072035] /axi/interrupt-controller@f9010000: Fixed dependency cycle(s) with /axi/interrupt-controller@f9010000 [ 1.085826] /axi/pcie@fd0e0000: Fixed dependency cycle(s) with /axi/pcie@fd0e0000 [ 1.089670] /axi/pcie@fd0e0000: Fixed dependency cycle(s) with /axi/pcie@fd0e0000/legacy-interrupt-controller [ 1.106399] /axi/display@fd4a0000: Fixed dependency cycle(s) with /dpcon [ 1.107515] /dpcon: Fixed dependency cycle(s) with /axi/display@fd4a0000 [ 1.120795] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 1.121940] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 1.128215] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 1.135000] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 1.141263] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 1.148048] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 1.154314] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 1.161099] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 1.235456] raid6: neonx8 gen() 2270 MB/s [ 1.303520] raid6: neonx4 gen() 2224 MB/s [ 1.371607] raid6: neonx2 gen() 2124 MB/s [ 1.439688] raid6: neonx1 gen() 1811 MB/s [ 1.507759] raid6: int64x8 gen() 1415 MB/s [ 1.575836] raid6: int64x4 gen() 1569 MB/s [ 1.643903] raid6: int64x2 gen() 1399 MB/s [ 1.711987] raid6: int64x1 gen() 1034 MB/s [ 1.712028] raid6: using algorithm neonx8 gen() 2270 MB/s [ 1.784069] raid6: .... xor() 1655 MB/s, rmw enabled [ 1.784115] raid6: using neon recovery algorithm [ 1.788783] iommu: Default domain type: Translated [ 1.792796] iommu: DMA domain TLB invalidation policy: strict mode [ 1.802942] SCSI subsystem initialized [ 1.803163] usbcore: registered new interface driver usbfs [ 1.808219] usbcore: registered new interface driver hub [ 1.813527] usbcore: registered new device driver usb [ 1.818642] mc: Linux media interface: v0.10 [ 1.822841] videodev: Linux video capture interface: v2.00 [ 1.828318] pps_core: LinuxPPS API ver. 1 registered [ 1.833255] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.842399] PTP clock support registered [ 1.846326] EDAC MC: Ver: 3.0.0 [ 1.849675] scmi_core: SCMI protocol bus registered [ 1.854431] efivars: Registered efivars operations [ 1.859297] zynqmp-ipi-mbox mailbox@ff9905c0: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.867987] zynqmp-ipi-mbox child@ff300000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.876070] zynqmp-ipi-mbox child@ff310000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.884412] zynqmp-ipi-mbox child@ff320000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.892761] zynqmp-ipi-mbox child@ff330000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.901119] zynqmp-ipi-mbox child@ff331000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.909472] zynqmp-ipi-mbox child@ff332000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.917819] zynqmp-ipi-mbox child@ff333000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.926175] zynqmp-ipi-mbox child@ff340000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.934531] zynqmp-ipi-mbox child@ff350000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.942964] zynqmp-ipi-mbox child@ff300000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.951236] zynqmp-ipi-mbox child@ff310000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.959584] zynqmp-ipi-mbox child@ff320000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.967941] zynqmp-ipi-mbox child@ff330000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.976291] zynqmp-ipi-mbox child@ff331000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.984642] zynqmp-ipi-mbox child@ff332000: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.992997] zynqmp-ipi-mbox child@ff333000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.001354] zynqmp-ipi-mbox child@ff340000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.009701] zynqmp-ipi-mbox child@ff350000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.018190] zynqmp-ipi-mbox child@ff300000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.026415] zynqmp-ipi-mbox child@ff310000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.034762] zynqmp-ipi-mbox child@ff320000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.043112] zynqmp-ipi-mbox child@ff330000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.051469] zynqmp-ipi-mbox child@ff331000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.059818] zynqmp-ipi-mbox child@ff332000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.068174] zynqmp-ipi-mbox child@ff333000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.076526] zynqmp-ipi-mbox child@ff340000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.084883] zynqmp-ipi-mbox child@ff350000: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.093575] FPGA manager framework [ 2.096796] Advanced Linux Sound Architecture Driver Initialized. [ 2.103272] Bluetooth: Core ver 2.22 [ 2.106209] NET: Registered PF_BLUETOOTH protocol family [ 2.111509] Bluetooth: HCI device and connection manager initialized [ 2.117872] Bluetooth: HCI socket layer initialized [ 2.122732] Bluetooth: L2CAP socket layer initialized [ 2.127783] Bluetooth: SCO socket layer initialized [ 2.135770] clocksource: Switched to clocksource arch_sys_counter [ 2.139111] VFS: Disk quotas dquot_6.6.0 [ 2.142676] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.155916] NET: Registered PF_INET protocol family [ 2.156123] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 2.165364] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 2.171112] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 2.178832] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 2.186945] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) [ 2.194893] TCP: Hash tables configured (established 32768 bind 32768) [ 2.200736] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 2.207436] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 2.214642] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 2.220637] RPC: Registered named UNIX socket transport module. [ 2.226077] RPC: Registered udp transport module. [ 2.230769] RPC: Registered tcp transport module. [ 2.235467] RPC: Registered tcp-with-tls transport module. [ 2.240948] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.247395] PCI: CLS 0 bytes, default 64 [ 2.252681] Initialise system trusted keyrings [ 2.255865] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 2.262435] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.268323] NFS: Registering the id_resolver key type [ 2.273078] Key type id_resolver registered [ 2.277233] Key type id_legacy registered [ 2.281250] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.287940] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.295487] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 2.358170] NET: Registered PF_ALG protocol family [ 2.358222] xor: measuring software checksum speed [ 2.363412] 8regs : 2519 MB/sec [ 2.367765] 32regs : 2510 MB/sec [ 2.372197] arm64_neon : 2352 MB/sec [ 2.375153] xor: using function: 8regs (2519 MB/sec) [ 2.380123] Key type asymmetric registered [ 2.384209] Asymmetric key parser 'x509' registered [ 2.389123] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 2.396572] io scheduler mq-deadline registered [ 2.401006] io scheduler kyber registered [ 2.405023] io scheduler bfq registered [ 2.411860] irq-xilinx: /amba_pl/interrupt-controller@80020000: num_irq=1, edge=0x1 [ 2.418446] ledtrig-cpu: registered to indicate activity on CPUs [ 2.461252] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.463772] Serial: AMBA driver [ 2.475320] brd: module loaded [ 2.479054] loop: module loaded [ 2.495918] CAN device driver interface [ 2.497212] usbcore: registered new interface driver asix [ 2.499534] usbcore: registered new interface driver ax88179_178a [ 2.505638] usbcore: registered new interface driver cdc_ether [ 2.511465] usbcore: registered new interface driver net1080 [ 2.517119] usbcore: registered new interface driver cdc_subset [ 2.523038] usbcore: registered new interface driver zaurus [ 2.528607] usbcore: registered new interface driver cdc_ncm [ 2.534262] usbcore: registered new interface driver r8153_ecm [ 2.540331] VFIO - User Level meta-driver version: 0.3 [ 2.546098] usbcore: registered new interface driver uas [ 2.550536] usbcore: registered new interface driver usb-storage [ 2.556520] usbcore: registered new device driver onboard-usb-dev [ 2.564021] rtc_zynqmp ffa60000.rtc: registered as rtc0 [ 2.567831] rtc_zynqmp ffa60000.rtc: setting system clock to 2025-10-30T23:31:17 UTC (1761867077) [ 2.576780] i2c_dev: i2c /dev entries driver [ 2.583298] usbcore: registered new interface driver uvcvideo [ 2.586705] Driver for 1-wire Dallas network protocol. [ 2.593049] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 2.600905] Bluetooth: HCI UART driver ver 2.3 [ 2.605149] Bluetooth: HCI UART protocol H4 registered [ 2.610281] Bluetooth: HCI UART protocol BCSP registered [ 2.615601] Bluetooth: HCI UART protocol LL registered [ 2.620722] Bluetooth: HCI UART protocol ATH3K registered [ 2.626125] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 2.632427] Bluetooth: HCI UART protocol Intel registered [ 2.637786] Bluetooth: HCI UART protocol QCA registered [ 2.643031] usbcore: registered new interface driver bcm203x [ 2.648682] usbcore: registered new interface driver bpa10x [ 2.654246] usbcore: registered new interface driver bfusb [ 2.659735] usbcore: registered new interface driver btusb [ 2.665230] usbcore: registered new interface driver ath3k [ 2.670792] EDAC MC: ECC not enabled [ 2.674607] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) [ 2.686928] sdhci: Secure Digital Host Controller Interface driver [ 2.692593] sdhci: Copyright(c) Pierre Ossman [ 2.696936] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.703441] SMCCC: SOC_ID: ID = jep106:0049:0000 Revision = 0x24738093 [ 2.709202] zynqmp_firmware_probe Platform Management API v1.1 [ 2.714961] zynqmp_firmware_probe Trustzone version v1.0 [ 2.752691] securefw securefw: securefw probed [ 2.752904] xilinx_ecdsa xilinx_ecdsa.0: ECDSA is not supported on the platform [ 2.759203] zynqmp-aes zynqmp-aes.0: will run requests pump with realtime priority [ 2.766694] usbcore: registered new interface driver usbhid [ 2.772058] usbhid: USB HID core driver [ 2.779651] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available [ 2.786759] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 2.792311] usbcore: registered new interface driver snd-usb-audio [ 2.798591] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 2.806159] IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP) [ 2.811384] IPVS: Connection hash table configured (size=4096, memory=32Kbytes) [ 2.818796] IPVS: ipvs loaded. [ 2.821835] Initializing XFRM netlink socket [ 2.826031] NET: Registered PF_INET6 protocol family [ 2.831617] Segment Routing with IPv6 [ 2.834640] In-situ OAM (IOAM) with IPv6 [ 2.838594] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.844812] NET: Registered PF_PACKET protocol family [ 2.849489] NET: Registered PF_KEY protocol family [ 2.854297] Bridge firewalling registered [ 2.858269] can: controller area network core [ 2.862643] NET: Registered PF_CAN protocol family [ 2.867405] can: raw protocol [ 2.870364] can: broadcast manager protocol [ 2.874545] can: netlink gateway - max_hops=1 [ 2.878980] Bluetooth: RFCOMM TTY layer initialized [ 2.883768] Bluetooth: RFCOMM socket layer initialized [ 2.888956] Bluetooth: RFCOMM ver 1.11 [ 2.892642] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.897943] Bluetooth: BNEP filters: protocol multicast [ 2.903165] Bluetooth: BNEP socket layer initialized [ 2.908135] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.914043] Bluetooth: HIDP socket layer initialized [ 2.919035] 8021q: 802.1Q VLAN Support v1.8 [ 2.923438] 9pnet: Installing 9P2000 support [ 2.927476] Key type dns_resolver registered [ 2.931831] NET: Registered PF_VSOCK protocol family [ 2.946599] registered taskstats version 1 [ 2.946737] Loading compiled-in X.509 certificates [ 2.959256] Btrfs loaded, zoned=no, fsverity=no [ 3.140846] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 26, base_baud = 6249375) is a xuartps [ 3.149931] printk: legacy console [ttyPS0] enabled [ 3.149931] printk: legacy console [ttyPS0] enabled [ 3.154859] printk: legacy bootconsole [cdns0] disabled [ 3.154859] printk: legacy bootconsole [cdns0] disabled [ 3.166091] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 27, base_baud = 6249375) is a xuartps [ 3.179524] of-fpga-region fpga-region: FPGA Region probed [ 3.187838] nwl-pcie fd0e0000.pcie: host bridge /axi/pcie@fd0e0000 ranges: [ 3.194753] nwl-pcie fd0e0000.pcie: MEM 0x00e0000000..0x00efffffff -> 0x00e0000000 [ 3.202777] nwl-pcie fd0e0000.pcie: MEM 0x0600000000..0x07ffffffff -> 0x0600000000 [ 3.210929] nwl-pcie fd0e0000.pcie: Link is DOWN [ 3.216098] nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00 [ 3.222290] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.227774] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 3.234648] pci_bus 0000:00: root bus resource [mem 0x600000000-0x7ffffffff pref] [ 3.242163] pci 0000:00:00.0: [10ee:d021] type 01 class 0x060400 PCIe Root Port [ 3.249489] pci 0000:00:00.0: PCI bridge to [bus 00] [ 3.254452] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 3.261247] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref] [ 3.269035] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 3.277844] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.285994] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.292622] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.297590] pci_bus 0000:00: resource 4 [mem 0xe0000000-0xefffffff] [ 3.303860] pci_bus 0000:00: resource 5 [mem 0x600000000-0x7ffffffff pref] [ 3.315006] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed [ 3.323934] spi-nor spi0.0: found mt25qu512a, expected m25p80 [ 3.330284] 3 fixed-partitions partitions found on MTD device spi0.0 [ 3.336658] Creating 3 MTD partitions on "spi0.0": [ 3.341456] 0x000000000000-0x000001e00000 : "qspi-boot" [ 3.347640] 0x000001e00000-0x000001e40000 : "qspi-bootenv" [ 3.353944] 0x000001e40000-0x000004240000 : "qspi-kernel" [ 3.365633] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 3.372406] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM [ 3.379074] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM [ 3.385741] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM [ 3.393091] i2c i2c-0: using pinctrl states for GPIO recovery [ 3.399031] i2c i2c-0: using generic GPIOs for recovery [ 3.404672] pca953x 0-0020: supply vcc not found, using dummy regulator [ 3.411369] pca953x 0-0020: using no AI [ 3.416565] pca953x 0-0021: supply vcc not found, using dummy regulator [ 3.423252] pca953x 0-0021: using no AI [ 3.427943] pca954x 0-0075: supply vdd not found, using dummy regulator [ 3.442659] i2c i2c-0: Added multiplexed i2c bus 2 [ 3.453795] i2c i2c-0: Added multiplexed i2c bus 3 [ 3.504031] i2c i2c-0: Added multiplexed i2c bus 4 [ 3.508972] i2c i2c-0: Added multiplexed i2c bus 5 [ 3.513777] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544 [ 3.521156] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 55 [ 3.528260] i2c i2c-1: using pinctrl states for GPIO recovery [ 3.534211] i2c i2c-1: using generic GPIOs for recovery [ 3.539867] pca954x 1-0074: supply vdd not found, using dummy regulator [ 3.546957] at24 6-0054: supply vcc not found, using dummy regulator [ 3.553893] at24 6-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write [ 3.560634] i2c i2c-1: Added multiplexed i2c bus 6 [ 3.566061] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.573374] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.580677] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.587986] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.595295] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.602604] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.609913] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.617214] si5341 7-0036: no regulator set, defaulting vdd_sel to 2.5V for out [ 3.625344] si5341 7-0036: Chip: 5341 Grade: 1 Rev: 1 [ 3.654518] i2c i2c-1: Added multiplexed i2c bus 7 [ 3.661594] si570 8-005d: registered, current frequency 300000000 Hz [ 3.667997] i2c i2c-1: Added multiplexed i2c bus 8 [ 3.675056] si570 9-005d: registered, current frequency 156250000 Hz [ 3.681459] i2c i2c-1: Added multiplexed i2c bus 9 [ 3.686489] si5324 10-0069: si5328 probed [ 3.741597] si5324 10-0069: si5328 probe successful [ 3.746520] i2c i2c-1: Added multiplexed i2c bus 10 [ 3.751542] i2c i2c-1: Added multiplexed i2c bus 11 [ 3.756571] i2c i2c-1: Added multiplexed i2c bus 12 [ 3.761592] i2c i2c-1: Added multiplexed i2c bus 13 [ 3.766475] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548 [ 3.774231] pca954x 1-0075: supply vdd not found, using dummy regulator [ 3.781173] i2c i2c-1: Added multiplexed i2c bus 14 [ 3.786209] i2c i2c-1: Added multiplexed i2c bus 15 [ 3.791234] i2c i2c-1: Added multiplexed i2c bus 16 [ 3.796267] i2c i2c-1: Added multiplexed i2c bus 17 [ 3.801295] i2c i2c-1: Added multiplexed i2c bus 18 [ 3.806328] i2c i2c-1: Added multiplexed i2c bus 19 [ 3.811360] i2c i2c-1: Added multiplexed i2c bus 20 [ 3.816396] i2c i2c-1: Added multiplexed i2c bus 21 [ 3.821292] pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548 [ 3.828902] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 56 [ 3.840791] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s [ 3.848489] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer with timeout 10s [ 3.856198] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1199880 KHz, changing to: 1200000 KHz [ 3.869230] [drm] Initialized zynqmp-dpsub 1.0.0 for fd4a0000.display on minor 0 [ 3.907296] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 3.962383] mmc0: new high speed SDHC card at address aaaa [ 3.968273] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 3.977997] mmcblk0: p1 p2 p3 p4 [ 4.915802] zynqmp-dpsub fd4a0000.display: [drm] Cannot find any crtc or sizes [ 4.924144] zynqmp-dpsub fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed [ 4.932401] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regulator [ 4.939975] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regulator [ 4.947453] ahci-ceva fd0c0000.ahci: supply target not found, using dummy regulator [ 4.965445] ahci-ceva fd0c0000.ahci: AHCI vers 0001.0301, 32 command slots, 6 Gbps, platform mode [ 4.974325] ahci-ceva fd0c0000.ahci: 2/2 ports implemented (port mask 0x3) [ 4.981195] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 4.991708] scsi host0: ahci-ceva [ 4.995389] scsi host1: ahci-ceva [ 4.998832] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 61 lpm-pol 0 [ 5.007614] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 61 lpm-pol 0 [ 5.020684] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 52 (4e:4a:f9:80:71:e4) [ 5.048755] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.054268] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 5.062041] xhci-hcd xhci-hcd.1.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x0000808002000810 [ 5.071478] xhci-hcd xhci-hcd.1.auto: irq 62, io mem 0xfe200000 [ 5.077512] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.083005] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 5.090675] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 5.097353] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12 [ 5.105622] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.112841] usb usb1: Product: xHCI Host Controller [ 5.117718] usb usb1: Manufacturer: Linux 6.12.40-xilinx-g3f587f532ea7 xhci-hcd [ 5.125019] usb usb1: SerialNumber: xhci-hcd.1.auto [ 5.130284] hub 1-0:1.0: USB hub found [ 5.134078] hub 1-0:1.0: 1 port detected [ 5.138368] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12 [ 5.146638] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.153863] usb usb2: Product: xHCI Host Controller [ 5.158736] usb usb2: Manufacturer: Linux 6.12.40-xilinx-g3f587f532ea7 xhci-hcd [ 5.166062] usb usb2: SerialNumber: xhci-hcd.1.auto [ 5.171242] hub 2-0:1.0: USB hub found [ 5.175011] hub 2-0:1.0: 1 port detected [ 5.179920] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 5.186990] of_cfs_init [ 5.189458] of_cfs_init: OK [ 5.192366] clk: Disabling unused clocks [ 5.197274] PM: genpd: Disabling unused power domains [ 5.202653] ALSA device list: [ 5.205613] #0: DisplayPort Monitor [ 5.330129] ata1: SATA link down (SStatus 0 SControl 330) [ 5.491777] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 330) [ 5.556701] ata2.00: ATA-8: ST3160215SCE, 3.ACF, max UDMA/133 [ 5.562451] ata2.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 32) [ 5.615008] ata2.00: configured for UDMA/133 [ 5.619569] scsi 1:0:0:0: Direct-Access ATA ST3160215SCE F PQ: 0 ANSI: 5 [ 5.628627] sd 1:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 5.636144] sd 1:0:0:0: [sda] Write Protect is off [ 5.639816] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd [ 5.647495] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.656632] sd 1:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 5.721365] sd 1:0:0:0: [sda] Attached SCSI disk [ 5.761578] usb 2-1: New USB device found, idVendor=054c, idProduct=09c2, bcdDevice= 1.00 [ 5.769776] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.776907] usb 2-1: Product: Storage Media [ 5.781090] usb 2-1: Manufacturer: Sony [ 5.784926] usb 2-1: SerialNumber: 5C07104BE29515C213 [ 5.791586] usb-storage 2-1:1.0: USB Mass Storage device detected [ 5.798012] scsi host2: usb-storage 2-1:1.0 [ 5.952353] EXT4-fs (mmcblk0p3): orphan cleanup on readonly fs [ 5.960052] EXT4-fs (mmcblk0p3): mounted filesystem 80c57074-5d0b-492d-9b18-5002b2ed582e ro with ordered data mode. Quota mode: none. [ 5.972118] zynqmp-dpsub fd4a0000.display: [drm] Cannot find any crtc or sizes [ 5.972137] VFS: Mounted root (ext4 filesystem) readonly on device 179:3. [ 5.989540] devtmpfs: mounted [ 5.993688] Freeing unused kernel memory: 4736K [ 5.998270] Run /sbin/init as init process [ 6.585311] systemd[1]: systemd 255.21^ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 6.617225] systemd[1]: Detected architecture arm64. Welcome to AMD Embedded Development Framework Linux distribution 25.11+development-5f383d8ae735e3dbfdb09cef4cce47cfa2c9dcc4 (scarthgap)! [ 6.659944] systemd[1]: Hostname set to . [ 6.676306] systemd[1]: Initializing machine ID from random generator. [ 6.682968] systemd[1]: Installed transient /etc/machine-id file. [ 6.897051] scsi 2:0:0:0: Direct-Access Sony Storage Media PMAP PQ: 0 ANSI: 6 [ 6.995777] systemd[1]: /usr/lib/systemd/system/xen-qemu-dom0-disk-backend.service:11: PIDFile= references a path below legacy directory /var/run/, updating /var/run/xen/qemu-dom0.pid → /run/xen/qemu-dom0.pid; please update the unit file accordingly. [ 7.299471] systemd[1]: Queued start job for default target Multi-User System. [ 7.344207] systemd[1]: Created slice Slice /system/getty. [ OK ] Created slice Slice /system/getty. [ 7.361581] systemd[1]: Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/modprobe. [ 7.381513] systemd[1]: Created slice Slice /system/serial-getty. [ OK ] Created slice Slice /system/serial-getty. [ 7.401078] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 7.420054] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 7.439975] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 7.459905] systemd[1]: Expecting device /dev/disk/by-label/boot... Expecting device /dev/disk/by-label/boot... [ 7.479835] systemd[1]: Expecting device /dev/disk/by-label/esp... Expecting device /dev/disk/by-label/esp... [ 7.495963] systemd[1]: Reached target Path Units. [ OK ] Reached target Path Units. [ 7.507872] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 7.523873] systemd[1]: Reached target Slice Units. [ OK ] Reached target Slice Units. [ 7.535894] systemd[1]: Reached target Swaps. [ OK ] Reached target Swaps. [ 7.573047] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 7.595953] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 7.612409] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 7.624085] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 7.644627] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 7.664181] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 7.684307] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 7.696399] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 7.724214] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 7.740174] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 7.756208] systemd[1]: Listening on User Database Manager Socket. [ OK ] Listening on User Database Manager Socket. [ 7.812032] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 7.827032] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 7.844054] systemd[1]: Mount /proc/xen files was skipped because of an unmet condition check (ConditionPathExists=/proc/xen). [ 7.858663] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 7.875124] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 7.894995] systemd[1]: Mounting Temporary Directory /tmp... Mounting Temporary Directory /tmp... [ 7.912269] systemd[1]: Starting Create List of Static Device Nodes... Starting Create List of Static Device Nodes... [ 7.935266] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 7.951465] systemd[1]: Starting Load Kernel Module dm_mod... Starting Load Kernel Module dm_mod... [ 7.971300] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 7.987385] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 8.003421] systemd[1]: Starting Load Kernel Module loop... Starting Load Kernel Module loop... [ 8.027444] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 8.043698] systemd[1]: Starting File System Check on Root Device... Starting File System Check on Root Device..[ 8.051865] sd 2:0:0:0: [sdb] 15199296 512-byte logical blocks: (7.78 GB/7.25 GiB) . [ 8.065056] sd 2:0:0:0: [sdb] Write Protect is off [ 8.070966] sd 2:0:0:0: [sdb] No Caching mode page found [ 8.076291] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 8.091006] systemd[1]: Starting Journal Service... Starting Journal Service... [ 8.110256] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 8.119600] systemd[1]: Starting Generate network units from Kernel command line... Starting Generate network units from Kernel com[ 8.130035] sdb: sdb1 mand line... [ 8.140686] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 8.144280] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 8.158445] systemd[1]: Started RPC Bind. [ OK ] Started RPC Bind. [ 8.163287] systemd[1]: Mounted Huge Pages File System. [ 8.173223] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File Sys[ 8.185337] systemd[1]: Mounted Kernel Debug File System. tem. [ OK ] Mounted Kernel Debug File Sys[ 8.196565] systemd[1]: Mounted Kernel Trace File System. tem. [ OK ] Mounted Kernel Trace File Sy[ 8.207942] systemd[1]: Mounted Temporary Directory /tmp. stem. [ OK ] Mounted Temporary Directo[ 8.219541] systemd[1]: Finished Create List of Static Device Nodes. ry /tmp. [ OK ] Finished Create List of[ 8.231565] systemd[1]: modprobe@configfs.service: Deactivated successfully. Static Device Nodes. [ 8.244294] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs[ 8.252491] systemd[1]: modprobe@dm_mod.service: Deactivated successfully. . [ 8.255737] systemd-journald[254]: Collecting audit messages is enabled. [ 8.264571] systemd[1]: Finished Load Kernel Module dm_mod. [ 8.272408] openvswitch: Open vSwitch switching datapath [ OK ] Finished Load Kernel Module dm_mod 8.285090] systemd[1]: modprobe@drm.service: Deactivated successfully. 0m. [ 8.297272] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm.[ 8.303865] systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 8.316875] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 8.336984] systemd[1]: modprobe@loop.service: Deactivated successfully. [ 8.344753] systemd[1]: Finished Load Kernel Module loop. [ OK ] Finished Load Kernel Module loop. [ 8.364943] systemd[1]: Finished File System Check on Root Device. [ OK ] Finished File System Check on Root Device. [ 8.384285] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Generate network units from Kernel command line. Mounting Kernel Configuration File System... Starting Remount Root and Kernel File Systems... Starting Repartition Root Disk... Starting Create Static Device Nodes in /dev gracefully... [ OK ] Mounted Kernel Configuration File System. [ 8.537247] EXT4-fs (mmcblk0p3): re-mounted 80c57074-5d0b-492d-9b18-5002b2ed582e r/w. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Repartition Root Disk. Starting Grow Root File System... Starting Flush Journal to Persistent Storage 8.623282] EXT4-fs (mmcblk0p3): resizing filesystem from 1572864 to 1572864 blocks m... [ OK ] Finished Create Static Device Nodes in /dev gracefully. Starting Create System Users... [ OK ] Finished Load Kernel Modules. [ 8.811118] systemd-journald[254]: Received client request to flush runtime journal. Mounting NFSD configuration filesystem... Starting Apply Kernel Variables... [ OK ] Finished Grow Root File System. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Mounted NFSD configuration filesystem. [ OK ] Finished Apply Kernel Variables. [ 8.934542] audit: type=1334 audit(1761867083.859:2): prog-id=6 op=LOAD [ 8.941263] audit: type=1334 audit(1761867083.859:3): prog-id=7 op=LOAD [ 8.947951] audit: type=1334 audit(1761867083.859:4): prog-id=8 op=LOAD Starting User Database Manager... [ OK ] Started User Database Manager. [ OK ] Finished Create System Users. [ OK ] Finished Coldplug All udev Devices. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. Mounting /var/volatile... [ 9.466640] audit: type=1334 audit(1761867084.391:5): prog-id=9 op=LOAD [ 9.473338] audit: type=1334 audit(1761867084.391:6): prog-id=10 op=LOAD Starting Rule-based Manager for Device Events and Files... [ OK ] Mounted /var/volatile. Starting Load/Save OS Random Seed... [ OK ] Started Rule-based Manager for Device Events and Files. [ 10.157296] macb ff0e0000.ethernet end0: renamed from eth0 [ 10.170305] random: crng init done [ OK ] Finished Load/Save OS Random Seed. [ OK ] Found device /dev/disk/by-label/boot. [ OK ] Found device /dev/disk/by-label/esp. Mounting /boot... Starting Load Kernel Module fuse... [ OK ] Finished Load Kernel Module fuse. [ 11.688375] EXT4-fs (mmcblk0p2): mounted filesystem 3302cf26-bf29-4e77-a2a9-463de35140a2 r/w with ordered data mode. Quota mode: none. [ OK ] Mounted /boot. Mounting /boot/efi... [ OK ] Mounted /boot/efi. [ OK ] Reached target Local File Systems. Starting Rebuild Dynamic Linker Cache... Starting Automatic Boot Loader Update... Starting Commit a transient machine-id on disk... Starting Create System Files and Directories... [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Starting Virtual Console Setup... [ OK ] Finished Create System Files and Directories. Starting Rebuild Journal Catalog... [ 12.472114] audit: type=1334 audit(1761867087.399:7): prog-id=11 op=LOAD Starting Network Name Resolution... [ 12.484222] audit: type=1334 audit(1761867087.411:8): prog-id=12 op=LOAD Starting Network Time Synchronization... Starting Record System Boot/Shutdown in UTMP... [ OK ] Finished Automatic Boot Loader Update. [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Finished Commit a transient machine-id on disk. [ OK ] Finished Rebuild Journal Catalog. [ OK ] Finished Virtual Console Setup. [ OK ] Started Network Name Resolution. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Finished Rebuild Dynamic Linker Cache. Starting Run pending postinsts... Starting Update is Completed... [ 16.076956] Unloading old XRT Linux kernel modules [ 16.089165] Loading new XRT Linux kernel modules [ OK ] Finished Update is Completed. [ 16.121063] zocl: loading out-of-tree module taints kernel. [ 16.232496] INFO: Creating ICD entry for Xilinx Platform [ 18.418180] audit: type=1334 audit(1761867093.343:9): prog-id=13 op=LOAD [ 18.425039] audit: type=1334 audit(1761867093.355:10): prog-id=6 op=UNLOAD [ 18.431950] audit: type=1334 audit(1761867093.363:11): prog-id=14 op=LOAD [ 18.438761] audit: type=1334 audit(1761867093.367:12): prog-id=15 op=LOAD [ 18.445558] audit: type=1334 audit(1761867093.367:13): prog-id=7 op=UNLOAD [ 18.452453] audit: type=1334 audit(1761867093.367:14): prog-id=8 op=UNLOAD [ 18.459341] audit: type=1334 audit(1761867093.375:15): prog-id=16 op=LOAD [ 18.466144] audit: type=1334 audit(1761867093.383:16): prog-id=17 op=LOAD [ 18.472946] audit: type=1334 audit(1761867093.383:17): prog-id=9 op=UNLOAD [ 18.479832] audit: type=1334 audit(1761867093.383:18): prog-id=10 op=UNLOAD [ OK ] Finished Run pending postinsts. [ OK ] Reached target System Initialization. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on D-Bus System Message Bus Socket. Starting Docker Socket for the API... Starting sshd.socket... [ OK ] Listening on Docker Socket for the API. [ OK ] Listening on sshd.socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. Starting Save/Restore Sound Card State... [ OK ] Started Job spooling tools. [ OK ] Started Periodic Command Scheduler. Starting D-Bus System Message Bus... Starting dfx-mgrd Dynamic Function eXchange... Starting IPv6 Packet Filtering Framework... Starting IPv4 Packet Filtering Framework... Starting Authorization Manager... [ OK ] Started System Logging Service. Starting User Login Management... Starting OpenSSH Key Generation... [ OK ] Started dfx-mgrd Dynamic Function eXchange. [ OK ] Finished Save/Restore Sound Card State. [ OK ] Started D-Bus System Message Bus. [ OK ] Finished IPv6 Packet Filtering Framework. [ OK ] Finished IPv4 Packet Filtering Framework. [ OK ] Reached target Preparation for Network. [ OK ] Reached target Sound Card. Starting dfx-mgrd Default Firmware Load Service... Starting Network Configuration... [ OK ] Started User Login Management. [ OK ] Finished dfx-mgrd Default Firmware Load Service. [ OK ] Started Network Configuration. [ OK ] Reached target Network. Starting containerd container runtime... Starting Wait for Network to be Configured... Starting Permit User Sessions... Starting Target Communication Framework agent... [ OK ] Started Xinetd A Powerful Replacement For Inetd. [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyPS0. [ OK ] Started Serial Getty on ttyPS1. [ OK ] Reached target Login Prompts. [ OK ] Started Target Communication Framework agent. [ OK ] Started Authorization Manager. Starting Modem Manager... [ OK ] Finished OpenSSH Key Generation. [ OK ] Started Modem Manager. [ OK ] Started containerd container runtime. [ OK ] Finished Wait for Network to be Configured. [ OK ] Reached target Network is Online. Starting Docker Application Container Engine... AMD Embedded Development Framework Linux distribution 25.11+development-5f383d8ae735e3dbfdb09cef4cce47cfa2c9dcc4 amd-edf ttyPS0 amd-edf login: amd-edf You are required to change your password immediately (administrator enforced). New password: Retype new password: Sorry, passwords do not match. Authentication token manipulation error AMD Embedded Development Framework Linux distribution 25.11+development-5f383d8ae735e3dbfdb09cef4cce47cfa2c9dcc4 amd-edf ttyPS0 amd-edf login: amd-edf You are required to change your password immediately (administrator enforced). New password: Retype new password: WARNING: AMD Embedded Development Framework is a reference Yocto Project distribution that should be used for testing and development purposes only. It is recommended that you create your own distribution for production use. amd-edf:~$ sudo -s We trust you have received the usual lecture from the local System Administrator. It usually boils down to these three things: #1) Respect the privacy of others. #2) Think before you type. #3) With great power comes great responsibility. For security reasons, the password you type will not be visible. Password: amd-edf:/home/amd-edf# ls /sys/bus/platform/devices/ | grep sha3 amd-edf:/home/amd-edf# dmesg | grep sha3 amd-edf:/home/amd-edf# which mkfs.cramfs /usr/sbin/mkfs.cramfs amd-edf:/home/amd-edf# ls /usr/sbin | grep util blkid.util-linux blockdev.util-linux brctl.bridge-utils chroot.coreutils fdisk.util-linux findfs.util-linux flash_eraseall.mtd-utils flash_lock.mtd-utils flash_unlock.mtd-utils flashcp.mtd-utils fsck.util-linux fsfreeze.util-linux fstrim.util-linux hwclock.util-linux losetup.util-linux mkswap.util-linux nanddump.mtd-utils nandwrite.mtd-utils nologin.util-linux pivot_root.util-linux readprofile.util-linux rfkill.util-linux rtcwake.util-linux sulogin.util-linux swapoff.util-linux swapon.util-linux switch_root.util-linux amd-edf:/home/amd-edf# mkfs.cramfs --version mkfs.cramfs from util-linux 2.40.4 amd-edf:/home/amd-edf#